PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER

STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-10-1-1-T

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter

₱21,875.00 ₱175,000.00

STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-15-1-1-T

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburrY type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support-less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

₱28,125.00 ₱22,500.00

STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-20-1-1-T

This depends upon the depth of the borehole to ground level and then the distance from the ground level to the final end point e.g. where the water tank is sited. The further the distance, the higher the pressure requirements of the borehole pump to prevent the water from trickling out. Submersible borehole pumps are a type of submersible pump. They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled. Starter borehole pumps can run for up to 24 hours. However, your everyday borehole pump will run between 6 & 8 hours. It is not good for your borehole pump to run continuously. If you run electrical pumps continuously, your utility bill will skyrocket.

₱30,625.00 ₱22,500.00

STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-30-1-1-T

The diameter of the borehole is usually around 120 to 160 mm, and its depth can reach up to 300 meters, although depth of about 40 meters is more common. Your pump and its control system must also meet the specific conditions as well as the high demands on reliability. This depends upon the depth of the borehole to ground level and then the distance from the ground level to the final end point e.g. where the water tank is sited. The further the distance, the higher the pressure requirements of the borehole pump to prevent the water from trickling out. Submersible borehole pumps are a type of submersible pump . They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled.

₱43,125.00 ₱34,500.00

STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-30-3-2-T

The diameter of the borehole is usually around 120 to 160 mm, and its depth can reach up to 300 meters, although depth of about 40 meters is more common. Your pump and its control system must also meet the specific conditions as well as the high demands on reliability. This depends upon the depth of the borehole to ground level and then the distance from the ground level to the final end point e.g. where the water tank is sited. The further the distance, the higher the pressure requirements of the borehole pump to prevent the water from trickling out. Submersible borehole pumps are a type of submersible pump. They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled.

₱36,250.00 ₱29,000.00

STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-50-1-1-T

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburry type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support-less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by t he internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30 °C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

₱66,500.00 ₱53,200.00

STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-50-3-2-T

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburry type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent wel l water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support-less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel : including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

₱62,500.00 ₱50,000.00

STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS4-75-3-1-T

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburry type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support- less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

₱93,750.00 ₱75,000.00

STAINLESS STEEL SUBMERSIBLE BOREHOLE MOTOR FOR 4" & 6" WELL CASING DIAMETER - MS6-100-3-2-T

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburry type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support-less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

₱101,875.00 ₱81,500.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-3-9

Submersible borehole pumps are a type of submersible pump. They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled. The water from the well or reservoir flows into the pump through the foot valve and strikes the impeller, which has multiple fixed blades. This impeller is connected to an electrical motor via a shaft and rotates in conjunction with the shaft. Submersibles are underwater robots that are deployed from the ship to the sea, where they record and collect information from the ocean's water column and seafloor for scientific analysis. A submersible pump is installed underwater whereas a centrifugal pump is installed on the ground. Therefore, submersible pumps are used for groundwater extraction through deep wells and centrifugal pumps are ideal for water supply and drainage applications in urban areas or for industrial purposes.

₱17,500.00 ₱14,000.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-3-13

The water from the well or reservoir flows into the pump through the foot valve and strikes the impeller, which has multiple fixed blades. his impeller is connected to an electrical motor via a shaft and rotates in conjunction with the shaft. Submersibles are underwater robots that are deployed from the ship to the sea, where they record and collect information from the ocean's water column and seafloor for scientific analysis. A submersible pump is installed underwater whereas a centrifugal pump is installed on the ground. Therefore, submersible pumps are used for groundwater extraction through deep wells and centrifugal pumps are ideal for water supply and drainage applications in urban aras or for industrial purposes. A wellbore is a type of borehole, which is a narrow shaft that is drilled into the ground—either horizontally or vertically—to extract water, petroleum, or gases. Other reasons for drilling boreholes include mineral exploration, environmental site assessment, and temperature measurement.

₱22,500.00 ₱18,000.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-3-17

A wellbore is a type of borehole, which is a narrow shaft that is drilled into the ground —either horizontally or vertically—to extract water, petroleum, or gases. Other reasons for drilling boreholes include mineral exploration, environmental site assessment, and temperature measurement. A submersible pump is installed underwater whereas a centrifugal pump is installed on the ground. Therefore, submersible pumps are used for groundwater extraction through deep wells and centrifugal pumps are ideal for water supply and drainage application s in urban areas or for industrial purposes. A submersible pump is a unit combining a pump and a motor to an enclosed unit, suitable for submerged installation. There are two types of submerged pumps: A submerged pump type with a submersible motor. A submerged pump with a dry motor, which is connected to the pump by a long shaft. As the name suggests, a submersible pump is designed to work with the entire assembly, consisting of pump and motor, fully submerged in the liquid or medium to be processed. This type of pump has a hermetically sealed motor which is close-coupled to the pump body.

₱26,875.00 ₱21,500.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-3-23

As the name suggests, a submersible pump is designed to work with the entire assembly, consisting of pump and motor, fully submerged in the liquid or medium to be processed. This type of pump has a hermetically sealed motor which is close-coupled to the pump body. It efficiently pushes fluids to the surface by converting rotary energy into kinetic energy. Commonly used for water supply, drainage, and irrigation systems, submersible pumps are reliable and self-priming, making them essential in various industrial and domestic applications. A submersible pump is installed underwater whereas a centrifugal pump is installed on the ground. Therefore, submersible pumps are used for groundwater extraction through deep wells and centrifugal pumps are ideal for water supply and drainage applications in urban areas or for industrial purposes. A water pump is used to move, compress, or transfer water from a lower level to a higher one. The main purpose of a water pump is to transfer water between two points and to get rid of excess water. It is often used in construction sites, tunnels, river beds, residential buildings, etc.

₱34,000.00 ₱27,500.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-5-7

A water pump is used to move, compress, or transfer water from a lower level to a higher one. The main purpose of a water pump is to transfer water between two points and to get rid of excess water. It is often used in construction sites, tunnels, river beds, residential buildings, etc.Dry running of the pump can damage the mechanical seal and the motor. For this reason, the float switches should be arranged so that the fill level in the shaft does not fall below the minimum level required to operate the pump. Wells are extremely important to all societies. In many places wells provide a reliable and ample supply of water for home uses, irrigation, and industries. Where surface water is scarce, such as in deserts, people couldn't survive and thrive without groundwater, and people use wells to get at underground water. Texmo Submersible Pumps. If you want to buy a pump, which is easy to install, easy to maintain, and is an extremely low weight to power ratio, then you should consider buying a Texmo submersible pump. The boreholes themselves are generally much narrower and deeper than a traditional well as a result of modern techniques. Due to the increased depth, a water borehole can provide a consistent and reliable source of water.

₱15,625.00 ₱12,500.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-5-9

Submersible borehole pumps are a type of submersible pump. They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled. The water from the well or reservoir flows into the pump through the foot valve and strikes the impeller, which has multiple fixed blades. This impeller is connected to an electrical motor via a shaft and rotates in conjunction with the shaft. Submersibles are underwater robots that are deployed from the ship to the sea, where they record and collect information from the ocean's water column and seafloor for scientific analysis. A wellbore is a type of borehole , which is a narrow shaft that is drilled into the ground—either horizontally or vertically—to extract water, petroleum, or gases. Other reasons for drilling boreholes include mineral exploration, environmental site assessment, and temperature measurement.

₱18,125.00 ₱14,500.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-5-11

A wellbore is a type of borehole, which is a narrow shaft that is drilled into the ground —either horizontally or vertically—to extract water, petroleum, or gases. Other reasons for drilling boreholes include mineral exploration, environmental site assessment, A submersible pump is installed underwater whereas a centrifugal pump is installed on the ground. Therefore, submersible pumps are used for groundwater extraction through deep wells and centrifugal pumps are ideal for water supply and drainage applications in urban areas or for industrial purposes. Underground natural mineral water often flows through permeable chalk and rock. The filtration through the rock layers means that this water can be of the highest quality. A borehole water supply is a deep well that accesses this underground water with a high- efficiency pump. It efficiently pushes fluids to the surface by converting rotary energy into kinetic energy. Commonly used for water supply, drainage, and irrigation systems, submersible pumps are reliable and self-priming, making them essential in various industrial and domestic applications. A submersible pump is a unit combining a pump and a motor to an enclosed unit, suitable for submerged installation. There are two types of submerged pumps: A submerged pump type with a submersible motor. A submerged pump with a dry motor, which is connected to the pump by a long shaft.

₱20,250.00 ₱16,200.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-5-15

A submersible pump is a unit combining a pump and a motor to an enclosed unit, suitable for submerged installation. There are two types of submerged pumps: A submerged pump type with a submersible motor. A submerged pump with a dry motor, which is connected to the pump by a long shaft. It efficiently pushes fluids to the surface by converting rotary energy into kinetic energy. Commonly used for water supply, drainage, and irrigation systems, submersible pumps are reliable and self-priming, making them essential in various industrial and domestic applications. Underground natural mineral water often flows through permeable chalk and rock. The filtration through the rock layers means that this water can be of the highest quality. A borehole water supply is a deep well that accesses this underground water with a high-efficiency pump. A submersible pump is installed underwater whereas a centrifugal pump is installed on the ground. Therefore, submersible pumps are used for groundwate r extraction through deep wells and centrifugal pumps are ideal for water supply and drainage applications in urban areas or for industrial purposes.

₱25,000.00 ₱20,000.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-5-21

Submersible borehole pumps are a type of submersible pump. They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled. The water from the well or reservoir flows into the pump through the foot valve and strikes the impeller, which has multiple fixed blades . This impeller is connected to an electrical motor via a shaft and rotates in conjunction with the shaft. Submersibles are underwater robots that are deployed from the ship to the sea, where they record and collect information from the ocean's water column and seafloor for scientific analysis. A wellbore is a type of borehole, which is a narrow shaft that is drilled into the ground—either horizontally or vertically—to extract water, petroleum, or gases. Other reasons for drilling boreholes include mineral exploration, environmental site assessment, and temperature measurement. Underground natural mineral water often flows through permeable chalk and rock. The filtration through the rock layers means that this water can be of the highest quality. A borehole water supply is a deep well that accesses this underground water with a high-efficiency pump. It efficiently pushes fluids to the surface by converting rotary energy into kinetic energy. Commonly used for water supply, drainage, and irrigation systems, submersible pumps are reliable and self-priming, making them essential in various industrial and domestic applications. Bladder Pumps. ... Grinder Pumps. ... Deep Well Pumps. ... Borehole Submersible Pumps. ... Dry Pit Submersible Pumps. ... Stainless Steel Submersible Pumps. ... Oil Filled Pumps. ... Submersible Utility Pumps.

₱32,500.00 ₱26,000.00

PSS SERIES STAINLESS STEEL SUBMERSIBLE BOREHOLE PUMP FOR 4" & 6" WELL CASING DIAMETER - PSS-5-21

Newsletter Subscription