Screwking Hardware Corp.

CONTROL BOX - CB -20125 POWER (HP) 2.0 PHASE 1 to control the various mechanical functions of industrial equipment or machinery

POWER HP 3.0 PHASE 1 to control the various mechanical functions of industrial equipment or machinery

POWER 5.0 PHASE 1 to control the various mechanical functions of industrial equipment or machinery.

Pressure boosting of water from roof tank, breaktank, ground tank, other static water supply etc . Water supply from shallow well. his pump is for indoor installation. There are 3 Types of Pressure Pumps or Booster Pumps in the Pascali Range: Centrifugal Pumps. Peripheral Pumps. Self-Priming Jet Pumps.A “simplex” system with just a single pump is sufficient to handle most small demands assuming redundancy isn't required. However, if the application is for a hospital or other critical operation, a duplex is often specified for back-up.A booster pump is a device that increases low water pressure and flow. It provides the extra boost needed to bring your water pressure to the desired level. A water booster pump provides pressure to move water from a storage tank or throughout a whole house or commercial facility.

PERIPHERAL PUMP MATERIAL : CAST IRON HP: 0.50 VOLTAGE 220V - 60HZ RPM 3450

SHALLOW WELL JET PUMP MATERIAL : CAST IRON HP : 0.75 VOLTAGE : 220V - 60HZ RPM 3450

INTIAL JET 4-4 SHALLOW WELL JET PUMP CAST IRON 1.0 HP VOLTAGE : 220 V - 60HZ RPM 3450

WILO JET WJ SERIES - WJ-201-X-EM/6 MATERIAL STAINLESS STEEL HP 0.50 VOLTAGE 220 V - 60HZ RPM 3450

WILO PUMP WJ-202-X-EM 6/B SELF PRIMING PUMP STAINLESS STEEL 0.75 HP VOLTAGE 220 V - 60 HZ RPM 3450

WILO JET WJ SERIES - WJ-203-X-EM/6/B STAINLESS STEEL 1.0 HP VOLATGE 220 V - 60HZ RPM 3450

WILO DEEP WELL JET PUMP-1STG(NO ADAPTER) - DWP 1.0 MATERIAL : CAST IRON HP 1.0 VOLTAGE 220 V - 60HZ RPM 3450

DEEP WELL JET PUMP-2STG(NO ADAPTER) - DWP 1.5 MATERIAL : CAST IRON HP 1.5 VOLTAGE 220V - 60HZ RPM 3450

WILO DEEP WELL JET PUMP-2STG(NO ADAPTER) - DWP 2.0 CAST IRON HP 2.0 VOLTAGE : 220 V - 60HZ RPM 3450

WILO OPTIONAL ACCESSORIES ADAPTER + EJECTOR APPLICABLE FOR WILO DWP 1.0

WILO OPTIONAL ACCESSORIES - WL-DWP-A2+E ADAPTER + CHARGER FOR WILO DWP 1.5 & 2.0

MODELS : PBI L203MA , PBI-L403MA , PBI L404MA , PBI-L803MA , PBI L405MA Wilo Duplex / Triple Inverter Booster Pump System MHIKE Series Simplex Inverter Booster SystemMhike Series Model MHIKE-D404A MHIKE-W804UA MHIKE-T804UA Power Output (HP x Unit) 2 x 2 3.3 x 2 3.3 x 3 Power Supply (V/Hz)... Vendor: Wilo SKU: 631581120915 Availability: In Stock Product Type: Water Pump

PRO CERAM VB DRY Electroplated diamond drills designed for drilling all types of tiles found in the industry, will also give outstanding performance on hard and brittle materials such as marble, granite and porcelain. Connection: 10mm shank for 3 Jaw Chuck Power Drills Applications: For dry or wet drilling

PRO CERAM VB DRY Electroplated diamond drills designed for drilling all types of tiles found in the industry, will also give outstanding performance on hard and brittle materials such as marble, granite and porcelain. Connection: 10mm shank for 3 Jaw Chuck Power Drills Applications: For dry or wet drilling

PRO CERAM VB DRY Electroplated diamond drills designed for drilling all types of tiles found in the industry, will also give outstanding performance on hard and brittle materials such as marble, granite and porcelain. Connection: 10mm shank for 3 Jaw Chuck Power Drills Applications: For dry or wet drilling

INDUSTRIAL SERIES SUBMERSIBLE VORTEX SEWAGE PUMP BY EVERGUSH MODEL EF-05 , EFLO-10 , EF-20 , EF-30, EF-30T ,- EF-50T , EF-75T , EF-100T , EF-150T MOTOR SPECS : 2P dry or oil type motor * Insulation : F Class Protection : Ip68

SUBMERSIBLE WASTE WATER PUMP MODELS EA-30 & EA-75T EA-1~7.5 HP EA1/3 ~ 1/2 HP

EVERGUSH SUBMERSIBLE DREDGING SEWAGE PUMPS MODELS : EFD-50T & EFD-75T EFD-Series60 HzFeatures Superior abrasion resistant double mechanical seal made of silicon carbide (SIC) to ensure best seal effect and reduce abrasion from slurry. Equipped with stainless

EVERGUSH CPU-CONTROLLED AUTO BOOSTER SILENT PUMPS MODEL : ESV800 & ESV 400

Drill bits are cutting tool s used to create cylindrical holes, almost always of circular cross-section. Drill bits come in many sizes and have many uses. Bits are usually connected to a mechanism, often simply referred to as a drill, which rotates them and provides torque and axial force to create the hole. A drill bit is a cutting tool that's fitted into a power drill and used to cut holes in materials. They come in a wide variety of shapes and sizes, but they all have similar parts as follows: Point: the top, cone-shaped part of the drill bit that consists of a spur and cutting lip. A drill bit is the cutting device located at the end of a drilling machine's drill string. Like the bit on a hand-held drill, it creates a passage through the material into which it bores. It may assist — to some extent — in removing the material which it cuts away to form the passage. A drill is a power too l that uses a rotating drill bit. It is used to create holes in various materials, such as wood , metal, and plastic. Drills are commonly used in construction and carpentry work, as well as in plumbing and electrical work. To determine the size of the drill bit, you need to calculate the diameter of the hole that needs drilling. Drill bits with sizes between 1 mm and 20 mm in diamete r are the most common drill bits. The drill hole size should be the same size as the screw's central core diameter or slightly smaller.

Drill bits are cutting tool s used to create cylindrical holes, almost always of circular cross-section. Drill bits come in many sizes and have many uses. Bits are usually connected to a mechanism, often simply referred to as a drill, which rotates them and provides torque and axial force to create the hole. A drill bit is a cutting tool that's fitted into a power drill and used to cut holes in materials. They come in a wide variety of shapes and sizes, but they all have similar parts as follows: Point: the top, cone-shaped part of the drill bit that consists of a spur and cutting lip. A drill bit is the cutting device located at the end of a drilling machine's drill string. Like the bit on a hand-held drill, it creates a passage through the material into which it bores. It may assist — to some extent — in removing the material which it cuts away to form the passage. A drill is a power too l that uses a rotating drill bit. It is used to create holes in various materials, such as wood , metal, and plastic. Drills are commonly used in construction and carpentry work, as well as in plumbing and electrical work. To determine the size of the drill bit, you need to calculate the diameter of the hole that needs drilling. Drill bits with sizes between 1 mm and 20 mm in diamete r are the most common drill bits. The drill hole size should be the same size as the screw's central core diameter or slightly smaller.

Drill bits are cutting tool s used to create cylindrical holes, almost always of circular cross-section. Drill bits come in many sizes and have many uses. Bits are usually connected to a mechanism, often simply referred to as a drill, which rotates them and provides torque and axial force to create the hole. A drill bit is a cutting tool that's fitted into a power drill and used to cut holes in materials. They come in a wide variety of shapes and sizes, but they all have similar parts as follows: Point: the top, cone-shaped part of the drill bit that consists of a spur and cutting lip. A drill bit is the cutting device located at the end of a drilling machine's drill string. Like the bit on a hand-held drill, it creates a passage through the material into which it bores. It may assist — to some extent — in removing the material which it cuts away to form the passage. A drill is a power too l that uses a rotating drill bit. It is used to create holes in various materials, such as wood , metal, and plastic. Drills are commonly used in construction and carpentry work, as well as in plumbing and electrical work. To determine the size of the drill bit, you need to calculate the diameter of the hole that needs drilling. Drill bits with sizes between 1 mm and 20 mm in diamete r are the most common drill bits. The drill hole size should be the same size as the screw's central core diameter or slightly smaller.

Drill bits are cutting tool s used to create cylindrical holes, almost always of circular cross-section. Drill bits come in many sizes and have many uses. Bits are usually connected to a mechanism, often simply referred to as a drill, which rotates them and provides torque and axial force to create the hole. A drill bit is a cutting tool that's fitted into a power drill and used to cut holes in materials. They come in a wide variety of shapes and sizes, but they all have similar parts as follows: Point: the top, cone-shaped part of the drill bit that consists of a spur and cutting lip. A drill bit is the cutting device located at the end of a drilling machine's drill string. Like the bit on a hand-held drill, it creates a passage through the material into which it bores. It may assist — to some extent — in removing the material which it cuts away to form the passage. A drill is a power too l that uses a rotating drill bit. It is used to create holes in various materials, such as wood , metal, and plastic. Drills are commonly used in construction and carpentry work, as well as in plumbing and electrical work. To determine the size of the drill bit, you need to calculate the diameter of the hole that needs drilling. Drill bits with sizes between 1 mm and 20 mm in diamete r are the most common drill bits. The drill hole size should be the same size as the screw's central core diameter or slightly smaller.

Drill bits are cutting tool s used to create cylindrical holes, almost always of circular cross-section. Drill bits come in many sizes and have many uses. Bits are usually connected to a mechanism, often simply referred to as a drill, which rotates them and provides torque and axial force to create the hole. A drill bit is a cutting tool that's fitted into a power drill and used to cut holes in materials. They come in a wide variety of shapes and sizes, but they all have similar parts as follows: Point: the top, cone-shaped part of the drill bit that consists of a spur and cutting lip. A drill bit is the cutting device located at the end of a drilling machine's drill string. Like the bit on a hand-held drill, it creates a passage through the material into which it bores. It may assist — to some extent — in removing the material which it cuts away to form the passage. A drill is a power too l that uses a rotating drill bit. It is used to create holes in various materials, such as wood , metal, and plastic. Drills are commonly used in construction and carpentry work, as well as in plumbing and electrical work. To determine the size of the drill bit, you need to calculate the diameter of the hole that needs drilling. Drill bits with sizes between 1 mm and 20 mm in diamete r are the most common drill bits. The drill hole size should be the same size as the screw's central core diameter or slightly smaller.

Drill bits are cutting tool s used to create cylindrical holes, almost always of circular cross-section. Drill bits come in many sizes and have many uses. Bits are usually connected to a mechanism, often simply referred to as a drill, which rotates them and provides torque and axial force to create the hole. A drill bit is a cutting tool that's fitted into a power drill and used to cut holes in materials. They come in a wide variety of shapes and sizes, but they all have similar parts as follows: Point: the top, cone-shaped part of the drill bit that consists of a spur and cutting lip. A drill bit is the cutting device located at the end of a drilling machine's drill string. Like the bit on a hand-held drill, it creates a passage through the material into which it bores. It may assist — to some extent — in removing the material which it cuts away to form the passage. A drill is a power too l that uses a rotating drill bit. It is used to create holes in various materials, such as wood , metal, and plastic. Drills are commonly used in construction and carpentry work, as well as in plumbing and electrical work. To determine the size of the drill bit, you need to calculate the diameter of the hole that needs drilling. Drill bits with sizes between 1 mm and 20 mm in diamete r are the most common drill bits. The drill hole size should be the same size as the screw's central core diameter or slightly smaller.